-40%
Holley QFT AED CCS 4160 Adjustable Vacuum Secondary Housing Kit Free Shipping
€ 9.93
- Description
- Size Guide
Description
NEW Holley QFT AED CCS 4160 Adjustable Vacuum Secondary Housing Kit Free ShippingSold as Each (1)
Adjustable Vacuum Secondary Housing - Polished Die Cast - Allows user to tune rate of secondary throttle opening by simply turning a screw.
CCS Adjustable Vacuum Secondary Housing Installation and Tuning Instructions
1. Remove old vacuum secondary housing. Note: If your carburetor is equipped with a choke it will be necessary to remove the choke housing and assembly to access all the screws securing the vacuum secondary housing.
2. Install new vacuum secondary housing. A new vacuum passage gasket has been cemented in place, check to be sure it is still positioned correctly.
3. Tighten all three screws to secure new vacuum secondary housing is place. Do not over-tighten these screws! Use a small, short screwdriver to avoid over-tightening. Reassemble and reinstall choke housing and assembly in reverse order of disassembly. If you experience any problems or difficulties, consult a service manual
4. Baseline setting for the adjustable needle is 1 1/2 turns off the seat, this setting has already been made during assembly at our facility. Should you ever need to re- establish your needle setting, lightly seat the needle. Do not over-tighten as this will alter the seat taper and could change the performance characteristics.
5. The Quick Set Adjustable Vacuum Secondary Housing incorporates a “Purple” spring. This ensures the secondaries will open fully on most applications. The purpose of the adjustment screw is to vary the opening rate, that is, when the secondaries begin to open as well as how quickly they open.
6. The secondary diaphragm operates off venturi vacuum. As airflow increases through the primary side of the carburetor, a vacuum is created in the venturi. It is this vacuum signal that actuates the secondary diaphragm. Without an accelerator pump on the secondary side of the carburetor it is necessary to graduate the secondary- opening rate. Air responds instantaneously when the throttle plates open, however, there is a delay before the fuel begins to flow.
7. For best performance you should not “feel” the secondaries opening. If you “feel” the secondaries open, do not confuse this feeling with better performance. That feel is actually a hesitation or a bog. Simply stated, the increased airflow has insufficient fuel to make a combustible mixture.
8. Best performance therefore is accomplished by determining what needle position creates a hesitation. Then gradually turn in the adjustment needle in 1/8-turn increments until the hesitation is eliminated. This will provide the optimum wide- open throttle acceleration.
9. The Quick Set Adjustment will allow you to tune for variations in traction, weather conditions, etc. How your engine responds to these conditions will determine where the adjustment screw should be set. This will require experimentation on your part; however, the Quick Set Adjustment will enable you to achieve the best performance possible under all conditions
Compatible with Today’s Complex Fuels
CCS Kits are supplied with the highest quality components that meet or exceed original equipment specifications and all CCS kits are compatible with today’s complex fuel
All returns must be pre-approved
before returning. Absolutely No Refund on installed items or returned items in non-sellable condition. Buyer to pay returned shipping Cost.
All Electrical items Carburetor Kits and Fuel Injection Kits will be shipped in sealed clear Package if the package is
un-wrapped
the item is nonreturnable.
Carburetor Collectible Specialty Thanks You for Your Support!
Please before leaving Feedback
If you receive an order that does not meet your
Expectations
, please permit us the opportunity to fix the problem before leaving negative feedback or rating us. Keep in mind our prices are controlled by eBay rating process. We strive for perfection and welcome the opportunity to correct any issues with your order. Your satisfaction is our #1 importance.
Shipping Time
Most items will be shipped Same business day if ordered before 10:00 a.m. EST. A delay in payment equals a delay in shipping. Our Pro-Series Carburetors with customer specs will be shipped within five days.
CCS Performance Carburetor is a complete service seller not an Empty Wagon Seller (drop shipper). Every item you see on our websites will be in stock and complete to ship within 24 hours of payment. In order to meet the price Competitive Ecommerce market, we purchase direct from the manufacturers in bulk quantities and package some items in house
Contact us.
Email is the quickest way to contact us. You will receive a response within 48 hours. Please limit your questions to the products we sell.
If you have purchased one of our Performance Series Carburetors a Tech Support phone number will be provided in the technical information supplied with each carburetor purchase.
Let CCS make your EBay experience a Great One!